Whirlpool Is Paying to Repair Some Refrigerators With Broken Door Wiring

Owners of certain Whirlpool, KitchenAid, Maytag and JennAir side-by-side refrigerators may not have to pay the full cost of repairing a broken freezer-door wire harness — and for some qualifying refrigerators, Whirlpool says it will cover both parts and labor.

An August 2026 Whirlpool technical service bulletin gives technicians mandatory instructions for diagnosing freezer-door wiring failures and establishes two special repair programs. Qualifying refrigerators within five years of age are covered for parts and labor under special project S25320. Refrigerators older than five years but no more than seven years old are covered for parts only under S11122.

The bulletin, Technical Service Pointer W11691025 Rev. B, applies to specified models and serial numbers and is connected to the class-action settlement over freezer-door wiring in certain Whirlpool-manufactured side-by-side refrigerators. Whirlpool emphasizes that the document is a service notice, not a recall.

What Whirlpool Is Covering

The amount Whirlpool covers depends on the refrigerator’s age. The bulletin says the date of manufacture determines age unless the owner has a purchase date available.

  • Up to five years old: Special project S25320 covers parts and labor.
  • More than five but up to seven years old: Special project S11122 covers the cost of parts only.
  • Older than seven years: The August service bulletin does not provide repair coverage under these two special-project codes.

Coverage is not based on the Whirlpool name alone. The refrigerator must fall within the model and serial ranges in the bulletin, and a technician must diagnose the problem. Owners should not assume that every ice-maker or dispenser problem is caused by broken door wiring.

Which Refrigerators Are Listed

Whirlpool lists a serial-number range of HR81800000 through HRA3999999. The service bulletin covers specified models sold under four Whirlpool-owned brands:

  • JennAir: JSC23C9EEM00.
  • KitchenAid: KRSC500ESS01; KRSC503E**01; KRSC700H*S00-04; KRSC703H*S00-04; KRSF505E**01; KRSF705HPS00-04; and KRSF705HBS00-01.
  • Maytag: MSC21C6MFZ00-05; MSS25C4MG*00-06; MSS26C6MFB00-01; MSS26C6MFW00-01; and MSS26C6MFZ00.
  • Whirlpool: WRS571CIHB00-04; WRS571CIH*00-04; WRS571CIDM02; WRS586FIEM04-05; WRS588FIH*00-04; WRS555SIH*00-06; WRS970CIDM00; WRS970CIHZ00-01; WRS973CIDM00; WRS973CIHV00-01; WRS973CIHZ00-01; WRSA71CIHN00; WRSA71CIHZ00-04; and WRSA88FIH*00-04.

Asterisks in Whirlpool’s model list are wildcards covering variants in that position. Owners should compare the complete model and serial number on the refrigerator’s identification label rather than relying on the beginning of a model number.

The Problem Can Look Like an Ice-Maker Failure

Whirlpool describes the possible customer complaint as little or no ice production in side-by-side refrigerators with an in-door ice maker. The problem may be intermittent.

But the bulletin does not tell technicians to assume that broken wiring is the cause. It directs them to check other possible explanations, including a freezer that is too warm, water-pressure or water-quality problems, a water-valve problem, restricted airflow, an ice maker that has been turned off, door or ice-bin switches, a frozen fill tube, the ice-maker thermistor and the high-voltage control board.

If those checks point toward an electrical problem — particularly an intermittent problem or a component receiving no voltage — Whirlpool tells technicians to inspect the harness running from the freezer door to the ice maker and test continuity between the connection at the bottom of the door and the ice-maker harness.

The bulletin notes that a technician may have to move the wire harness at the bottom of the freezer door while testing it to reveal an intermittent fault. That detail matters because a wire can make contact in one door position and lose it in another.

A Broken Wire Can Mean a New Freezer Door

If the harness is malfunctioning, Whirlpool instructs the technician to determine which side of the freezer-door connector contains the fault. When the problem is on the door side of the connector, the prescribed repair is to replace the freezer door with the replacement door listed for that model.

Whirlpool also gives technicians a specific installation instruction for the replacement: the new door’s wiring harness must be routed behind the refrigerator’s leveling leg and secured with a wire tie.

For consumers, that makes the special coverage particularly important. A failure embedded in the door can turn what sounds like a broken wire into a repair involving an entire freezer-door assembly.

How to Pursue a Covered Repair

Owners who think their refrigerator may be affected should start by recording the full model and serial number and the purchase date, if available. They should then contact Whirlpool or an authorized service provider and describe the symptoms rather than attempting to diagnose a wire-harness break themselves.

Ask the servicer to check whether the refrigerator qualifies under Technical Service Pointer W11691025 Rev. B and special project S25320 or S11122. The bulletin specifically tells servicers to check the model and serial list to confirm coverage before making the repair.

If broken freezer-door wiring is diagnosed, keep the service invoice and make sure the diagnosis of wire-harness breakage is documented. Whirlpool’s bulletin specifically tells technicians to advise owners to retain those records.

The Class-Action Settlement Can Provide Another Option

The service program is tied to the settlement of Costa v. Whirlpool Corp., a class action involving allegations that wiring leading to the freezer door in certain Whirlpool-manufactured side-by-side refrigerators could break and cause in-door functions to stop working. Whirlpool denied wrongdoing, and the settlement is not a finding that the refrigerators are defective.

Whirlpool’s service bulletin says all or part of the repair cost may be covered under the settlement. It also says owners with qualifying wire-harness breakage may elect to replace the refrigerator instead of having it repaired and may be eligible for reimbursement of the refrigerator’s original purchase price.

That option has procedural requirements. The bulletin tells technicians to direct owners to the official refrigerator settlement website or the settlement administrator at 1-877-335-4279. It also says reimbursement requests must be submitted within 90 days of the date the wire-harness breakage is diagnosed.

The settlement’s official FAQ contains additional requirements for future wire-harness issues, so an owner considering replacement rather than repair should review those terms and contact the administrator before paying for a replacement refrigerator.

Appliance News has previously published a guide to the settlement’s repair and replacement provisions. The August Whirlpool bulletin adds the service-department instructions: how technicians are supposed to diagnose the failure, when the freezer door should be replaced and which special-project codes provide parts or labor coverage.

What to Have Ready Before Calling

  • The refrigerator’s complete model number.
  • The complete serial number.
  • The original purchase date or receipt, if available.
  • A description of the symptoms, including whether the ice problem is intermittent or changes when the freezer door moves.
  • Any previous service invoices involving the freezer door, ice maker, dispenser or door wiring.

Consumers should also remember what the bulletin does not say. It is not a recall, and it does not establish that every refrigerator in the listed model families has broken wiring. It creates a repair procedure and coverage path for qualifying refrigerators when the specified failure is diagnosed.

Share This Article
Leave a Comment